Mix
of Nexus 5500 & Catalyst 6500?
Hi there,
Does Nexus 5500 series require a Nexus 7000
parent device? or it will be supported with Catalyst 6509?
If this is the scenario :
CAT6509 - Core Layer 3
CAT6509 - Distribution Layer 2/3
NX-5548 - Access Layer 2
And FYI, no VSS on Catalyst 6509.
Thanks in advance,
---A Q from Cisco Support Community.
For years, the Cisco Catalyst 6509 has been
the workhorse of small and medium-sized enterprises, used for access,
aggregation and core layers. Yet modern CPUs, motherboard chip architectures,
virtualization, and more powerful storage arrays are moving the data center
performance bottleneck back to the network infrastructure, creating demand
for performance that exceeds the 6509. While some might think the Cisco Nexus
7000 would be the obvious replacement, midsized companies could benefit more
with a Cisco Nexus 5500, specifically the Nexus 5596UP, as their network core
switch.
Why not just upgrade the Catalyst with a
Supervisor 2T to replace the core switch?
With new traffic demands on the Catalyst
6509, one upgrade option is certainly a new Supervisor and line cards to
keep the old 6509 fighting. However, those upgrades aren’t trivial
expenditures. Plus, it’s well known that Cisco has exhausted the raw
forwarding capability of the 6500 with the Supervisor 2T.
Why not go with the Nexus 7009 as a core
switch replacement?
The Cisco Nexus 7009 could be
viewed as the natural 6509 successor, as, its form factor is similar to the
6509, allowing for a forklift upgrade without having to allocate additional
rack units in the data center. Furthermore, the Nexus 7009 will even mount into
a 2-post rack while its bigger brothers, the 7010 and 7018, require a 4-post
rack. The Nexus 7K family of line cards also offers high port densities of
10GbE at favorable levels of oversubscription, as well as a migration path to
40GbE and 100GbE.
These are all great benefits, but the Nexus
7009 is a pricey bit of gear. Additionally, if an IT shop specifies a pair of
the gear to build in the resiliency, then it becomes pricey times two. The list
price for a Cisco Nexus 7009 bundle containing 2 Supervisor-1 engines, 5
Fabric-2 modules, and 2 6KW power supplies, the enterprise L3 feature license,
and a single Fabric-2 48-port 10GbE line card, totals up to a whopping
$157,500. That total doesn’t even include the 10GbE optics that must be
purchased. If you add a year of 24x7x4 SNTP SmartNet coverage, that’s another
$13,600 to add to the OPEX budget.
Enter the Nexus 5K: A network core
switch alternative
If the Supervisor 2T and Cisco Nexus 7009
aren’t the right fit, the question then becomes: what is a viable replacement
for the Catalyst 6509 that will meet growth demand for 10 GbE ports without
busting the budget? The market is replete with choices of densely packed 10 GbE
L3 switches from Juniper, Arista, Brocade, HP, and others. However, for a
Cisco-centric shop, the Nexus 5596UP could be the answer.
The Nexus 5596UP may have a small 2U
footprint in the data center, but packs a lot of packet forwarding punch,
offers multi-chassis link aggregation and fault-tolerance when configured
according to Cisco best practices.
Additionally, the Nexus 5596UP is a
non-blocking 10GbE switch that ships with 48 fixed ports and three slots that
can be populated with additional modules. In order to use the 5596UP as a core
switch, engineers will have to use one of those slots with the L3 routing
engine expansion card (Version 2 boosts maximum host count to 16K), while
leaving two blank slots that could be filled with 16 more 10GbE ports each.
Adding the L3 enterprise software license makes a 48-port, 10 GbE switch with a
full complement of routing features that can be expanded to 80 10GbE ports.
That’s quite a lot of network forwarding capacity crammed into a 2U form
factor. In fact, the Nexus 5596 has upsides at both L2 and L3:
- Non-blocking at L2: Every port on a 5596UP is capable of forwarding at line-rate, full-duplex without dropping a frame. At Layer 2, it’s theoretically impossible to overwhelm the 5596UP; a frame received is a frame delivered when a switch is non-blocking.
- Up to 160Gbps at L3 (240Mpps): While not a jaw-dropping statistic, 160Gbps of inter-VLAN traffic is a rather large number for a small enterprise, and not the sort of throughput that most small data centers are likely to approach. While aggregated vMotion, backup and storage traffic could potentially surge beyond the 160Gbps mark, most network designs isolate these sorts of traffic flows to a single VLAN. For example, vMotion traffic doesn’t get routed, therefore doesn’t take a chunk out of the 160Gbps number.
Will the Cisco Nexus 5596UP break the bank?
From a throughput perspective, the 5596UP
sounds reasonable for a small data center application. Yet, does the Nexus
5596UP meet core switch replacement and cost parameters? The
chassis, version 2 of the L3 routing engine and the enterprise L3 license, list
at a total of $51,800, plus $2,800 to the annual OPEX budget for 24x7x4
SmartNet coverage. Be sure not to overlook that OPEX number for annual SmartNet
renewal, as the number is over four times higher for the 7009 versus the
5596UP. Like the Nexus 7009 numbers listed above, this total does not include
optics, but note that the 7009 and 5596UP use the same optics. For comparison
purposes, the optics cost is a wash.
---Original reading from searchnetworking.techtarget.com
More
Notes:
Cisco Nexus 5500 Platform Switches
The Cisco Nexus 5500
Platform supports the following application scenarios, many of which require
the installation of other products:
•As
an access-layer switch, it can be used purely as a 1- and 10-Gigabit Ethernet
switch, consolidating 10 Gigabit Ethernet connections into a smaller number of
server connections trunked to the aggregation layer.
•As
a smaller-scale aggregation switch, it can be used as a Layer 3 1- and
10-Gigabit Ethernet switch, consolidating multiple 1- and 10-Gigabit Ethernet
connections from a data center access layer.
•In
conjunction with the Cisco Nexus 2248T GE Ethernet Fabric Extender, the Cisco
Nexus 5500 Platform can be a high-density 1-Gigabit Ethernet switching system,
consolidating more than 900 Gigabit Ethernet connections within a single
management plane.
•In
conjunction with the Cisco Nexus 2232T 10GE Fabric Extender, it can be a
high-density switching system, consolidating more than 600 10-Gigabit Ethernet
connections within a single management plane.
•In
conjunction with the Cisco Nexus 2224TM 10GE Fabric Extender, it can be a
high-density switching system, consolidating more than 600 10-Gigabit Ethernet
connections within a single management plane
•As
a rack-level I/O consolidation platform, the switch carries Ethernet traffic
from servers to the aggregation layer and carries FC traffic to existing Fibre
Channel SANs.
•As
a crucial element in data center I/O consolidation, the switch enables I/O
consolidation at the access layer and provides interoperability with the Cisco Nexus
5500 Platform and other standards-based products.
More Related: Cisco Nexus 5500 PlatformOverview
CiscoNexus 5000 Series Switches (Cisco Nexus 5548, Cisco Nexus 5596 Switches) Data
Sheet
CiscoCatalyst 6500 Switches: Cisco Catalyst
6000/6500, Aim at Enterprise Network & Service Provider Networks
No comments:
Post a Comment